Intake Manifold Fits: BMW Motorsport P45B20 race engine

Original BMW Works Carbon Fiber intake plenum for the BMW E90 320si STC, WTCC, ETC Chassis.

The P45B20 is a 4 cylinder 2.0 liter race engine used in the E90 4 door sedan 3 series race cars.

AMERICAN LE MANS SERIES 2006 CARBON FIBER E46 M3 GT2 PTG WIDE BODY

Front bumper

Front Bumper with Splitter Extensions

Splitter to Bumper Connector

Nose Floor

Front Fender Left

Front Fender Right

Rear Fender Left

Rear Fender Right

Rear Bumper

Dash Panel

Dash Switch Panel

BMW Motorsport E36 320i STC

Carbon Fiber Roof With Aero Groove NACA Duct

BMW NA Motorsport E46 M3 GT/GTR/GT2 works team PTG carbon fiber aerodynamic NACA duct roof.

BMW Motorsports Carbon Fiber Intake Manifold​

BMW NA Works Team PTG E46 M3 GTR/GT2

BMW E46 M3 GT/GTR/GT2 ROOF

CARBON FIBER CFK BMW Motorsport Intake Manifold PTG S50 Race Engine & NEW ALTERNATIVE P50 CARBON INTAKE 

 

This intake manifold evolved on a Motorsport race engine dyno under the team effort of the original BMW NA Motorsport works team PTG engine builder and carbon fiber race car parts castor. The reason this was done was because BMW AG Motorsport division has sold out of the original carbon fiber intake manifold for the E36 M3 GTR/GT2 ELMS, IMSA and ALMS factory works race cars. This new carbon fiber intake manifold was developed around BMW AG Motorsport E46 M3 GT2 carbon fiber intake plenum used on the P54B32 factory race engine. Many changes needed to take place to allow this S50/P50 PTG carbon fiber intake manifold to not only fit on the S50 race engine but also in the E36 M3 engine bay. Additional work went into catering to not only the S50 race engine but it was decided to make an additional version that would fit on the S50 street legal version in an E36 M3 street car chassis typically equipped with air-conditioning. The intake is bread from a master carbon fiber parts custom fabricator who worked for the BMW NA Motorsport works team PTG from 1995 until the team officially retired from BMW racing in 2007. This is a real race intake manifold and will not cave in under engine vacuum.
Custom S50/P50 MOTORSPORT INTAKE MANIFOLD COST: $4,750.00

NEW HAND CRAFTED ALTERNATIVE: The original BMW NA Motorsport works team PTG carbon parts fabricator Randy 1996 - 2006.
This new intake manifold developed to answer the demand for the BMW AG Motorsport S50/P50B30, S50/P50B32 & "S50/P50B34 PTG" BMW race engines.


BMW AG Motorsport factory race engine intake manifold S50B30/S50B32/P50B32:
1161 2700518 LUFTFÜHRUNG Air duct B32 Gr.A
N.L.A.
1161 2700519 ZWISCHENST. INTER PIECE B32 Gr.A
N.L.A.
1161 2700520 LUFTSAMMLER AIR COLLECT. S50B32 Gr.A
N.L.A.
1161 2700521 MANSCHETTE Collar
1161 2700522 LUFTFILTER Air
1161 2700668 CLEANING KIT CLEANING KIT BMC 250-355


N.L.A.No Longer Available

GRAND AM CARBON FIBER BODY KIT E46 M3 GT PTG

Front bumper

Splitter

Front Fender Left

Front Fender Right


Rear Fender Left

Rear Fender Right

Rear Bumper

Front Dive Plane Left

Front Dive Plane Right

BMW NA Works Team PTG E46 M3 GT GRAND AM Body

BMW E46 CARBON PANELS

BMW RACE CAR CARBON FIBER PARTS

Intake Manifold Fits: BMW Motorsport P54B20 race engine

Original BMW Works Carbon Fiber intake plenum for the BMW E46 320i WTCC, STCC, ETC race car engines and chassis.

The P54B20 is an inline six 2.0 liter race engine used in the E46 4 door sedan 3 series race cars.

BMW Motorsports Carbon Fiber Intake Manifold​

BMW AG MOTORSPORT F22 M235iR​ RACE CAR WIDE BODY KIT

WORLD CHALLENGE CARBON FIBER BODY KIT FOR THE E46 M3 GT PTG WORLD CHALLENGE RACE CAR

Front bumper

Front Bumper Nose Floor Air Splitter

Front Fender Left

Front Fender Right

Rear Bumper

BMW AG Motorsport factory carbon fiber intake manifold fits: S54B32, S54B34, P54B32, P54B34

Original BMW Works Carbon Fiber intake plenum for the BMW E46 M3 GT/GTR/GT2 Chassis and E86 Z4 VLN Chassis.

BMW Works Team PTG E36 M3 GT/GTR IMSA​

BMW NA Motorsport works team PTG E46 M3 GT

SCOTTSDALE MOTORSPORTS

BMW AG Motorsport factory original Super Touring Car aero parts.


BMW AG Motorsport E36 320 STC "Super Touring Car"


BMW raced the E36 sedan chassis with an FIA certified DMSB safety cage in the super touring car series of Europe powered by the S42 race engine that was an evolution of the S14 race engine. A rare Diesel spec E36 3 Series STC race car was also developed and raced in the 24 hour Nurburgring series and won on its maiden voyage.

BMW AG Motorsport interchangeable carbon fiber race car parts for the BMW E46 M3 GT, GTR & GT2

Door Left

Door Right

Trunk Lid

BMW AG Motorsport Classic S50B30 /// S50B32 /// S50B34​​

Factory original BMW AG Motorsport F22 M235iR race car wide body kit.


DESIGNED TO FIT: BMW 2 series with the F22 chassis, this BMW Motorsport race car body kit has over 100 parts in its quantity count.


OPTIONAL: BMW Motorsport (F22) M235iR BBS Motorsport rims and spacers

BMW AG Motorsport E36 M3 GTR & GT2 carbon fiber body panels

Authentic BMW Works Team PTG Carbon Fiber Panels for the BMW E36 M3 GTR Race Car.

OPTION #1. Made from the original molds by BMW AG Motorsport for the BMW E36 M3 GTR ELMS race car.


OPTION #2. Made from the original molds that had been owned by BMW NA Works race team PTG owner Thomas Milner.

(NOTES) 2 versions of the hood are available. Non ventilated was originally used by the BMW works PTG race team.

3 versions of the rear wing available as used by the original PTG race team.

BMW Motorsports Carbon Fiber Intake Manifold​

BMW E46 M3 GT PTG ALMS HOOD

Ventilated carbon fiber hood

E46 M3 GT Ventilated Hood